How to make an ostomy pouch cover

By Shakam | 20.07.2020

how to make an ostomy pouch cover

Oct 13,  · There are many different variations of sizes and shapes ostomy pouches. Learn how to make a template for your ostomy pouch cover and whip up some fabric covers. Oct 13,  · Grab two pencils and a piece of paper. Place the ostomy pouch onto your paper. Hold your two pencils together and draw around the pouch. So we need to add a circular opening, I have used a mug as a template. Do play with some scraps of fabric to check the circular opening size. My first ostomy pouch cover had too large an opening.

Ostomy pouch covers are cvoer of a fun way to spice up your ostomy life. Do you make your own pouch covers? Post on Instagram and tag me ostomyadventure!

This will give you a little extra fabric all the way around so you have some fabric to sew on. Cut the drawing out, cutting along the outermost edge as well as the larger of the two circles you drew for the flange opening. Place the stencil on the fabric and trace around the outer edge of your drawing. This will be the front of your pouch cover.

Move the stencil over and ho again around the outer edge of your drawing, and then also trace the perimeter of the flange opening you cut out. This will be the back of your pouch cover. Cut out the pieces you traced.

Step Three: Sewing an Ostomy Bag Cover Fold the darts from the back piece of your pouch cover toward the back of your fabric and pin them in place. Place the front and back pieces together so that the nice parts of the cvoer face inward toward each other.

You should see the folds from the darts on the outside when you have the nice parts of the fabric facing inward. Pin the fabric together. You can sew on zig zag or switch back to a straight stitch, just remember what to use to remove temporary tattoos reinforce the start and finish.

Fold the bottom part where it would drain up on either side and finish off the edges but remember not to sew both sides together! To put it on easily, grab the bottom part of your pouch through that bottom hole you left unsewn and then pull the rest of the pouch cover up and around so the flange opening of the pouch cover goes around your flange opening.

Share this: Email Facebook Twitter Pinterest. Like this: Like Loading Sorry, your blog cannot share posts by email.

What You'll Need

Follow these step-by-step instructions to make a custom-fit ostomy bag cover that can help with skin irritation and discretion. Article by shirley allen. Bag Patterns To Sew Sewing Patterns Colostomy Bag Covers Sewing Room Storage The Fold Line Pattern Making Step By Step Instructions Sewing Projects Sewing Ideas. Oct 19,  · This ostomy pouch cover is made from FLANNEL which creates a soft barrier between your skin and the ostomy pouch. The cover has an open end with a snap closure. The flannel fabric will feel soft and cozy against your skin.

Wearing an ostomy bag sometimes brings about concerns of skin irritation and discretion. But a DIY ostomy bag cover can help to resolve both of these issues. This project uses soft fabric in the color of your choice. It requires intermediate sewing skills and about two hours of your time to make. A major benefit of sewing the cover yourself is you can make it fit precisely for your variety of ostomy bag. The instructions will guide you through making a custom ostomy bag cover pattern for any shape and size.

If you use a belt, add snaps to the back of the bag cover and the belt to hold the bag cover in place. Also, consider making a tube of fabric to cover the belt and attach the bag cover. Making the front pattern piece:. If you are using a drainable pouch, close the bag. Keeping the bag flat, trace its edges onto your paper.

Cut out the pattern piece around the outer edges only. Don't cut out the flange opening, as you will be using this marking to create the back pattern piece. Making the back pattern piece:. Trace the outer edges of the front pattern piece. Measure 2 inches from the bottom edge, and draw a line across the pattern piece.

Adjust this measurement if appropriate for your bag. You'll want enough fabric to support the bottom of the bag, along with an opening that's close enough to the drain so you can access it without removing the entire cover. The line should land just above the drain area of the bag. Cut the pattern piece on the line you just created. Trace both pieces onto the paper.

Connect the new line to the pattern pieces, keeping the shape intact by tracing the edge of the original pattern piece to the new line. Trace the flange opening onto the upper back pattern piece. Cut out the opening. Fold the length of each pattern piece in half, aligning the edges.

Draw a straight line on the fold. You'll use these fold lines as your grain lines to lay out the pattern pieces. Spread the fabric out flat in a single layer. Press the fabric if necessary. Lay out the pattern pieces, using the marked grain lines to keep the fabric grain straight. Pin the pattern pieces in place, and then cut them out. Cut out the flange opening by tracing it or by using the pattern as a guide. Stabilize the edges of the flange opening by stay stitching close to the edge or by zigzag stitching on the edge of the opening.

Enclose the flange opening edge with the double-fold bias tape. Fold the end as you reach where you started sewing, and enclose the starting point with the folded end of the tape.

You might want to hand baste the bias tape in place before machine sewing. The smaller the flange opening is, the more helpful it is to baste first. If your fabric is prone to fraying, zigzag the raw edges of the pressed portion under the edge.

Then, sew the turned-under edges to the body of the fabric, forming a hemmed edge on both back sections. Lay the full front section on a flat surface. Next, lay the larger top back pieces on the front piece, aligning the edges. And lay the smaller bottom back section on the upper section, aligning the lower edges.

Pin the edges of the back sections, so the overlap is held in place. Baste the edges of the overlap to hold the two back pieces together. If you are using a silky fabric layer, baste the silky layer to the main fabric. Lay the front and back sections together with the right sides together, aligning the edges. Pin the layers together. Sew a second seam line on the seam allowance close to the first seam line. This will stop the fabric from fraying while not adding as much weight as zigzagging or most other seam finishes.

Turn the bag right side out, and press. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights.

Measure content performance. Develop and improve products. List of Partners vendors. Tip If you use a belt, add snaps to the back of the bag cover and the belt to hold the bag cover in place. Create a Pattern for the Ostomy Bag Cover Making the front pattern piece: If you are using a drainable pouch, close the bag.

Making the back pattern piece: Trace the outer edges of the front pattern piece. Show Full Article. Your Privacy Rights. To change or withdraw your consent choices for TheSpruceCrafts.

At any time, you can update your settings through the "EU Privacy" link at the bottom of any page. These choices will be signaled globally to our partners and will not affect browsing data. We and our partners process data to: Actively scan device characteristics for identification. I Accept Show Purposes.

4 thoughts on “How to make an ostomy pouch cover

  1. Gronris

    Excelente video, muy bien explicado. Muy agradecido, muy agradecido y muy agradecido.

    Reply
  2. Gojind

    The rapid shooting sound you made HAHAH great stuff

    Reply

Add a comment

Your email will not be published. Required fields are marked *